Brenner 8 Driver Windows 7
What about Brenner 8 USB pic & dsPic programmerit's free and is working great (tested with many pic and few dsPic)it's new recent (summer-winter 2006) and allready support 173 PIC modelsit can be used to program and/or to power pic from usb, in ZIF or In Circuiti use-it with 'universal programming module' from microchip (free also)if anyboby intered i will post here eagle files for programmer and programming module (boards are made by me)i will try to post some picturesfor personal message« Last Edit: January 17, 2007, 07:29:42 07:29 by eSilviu »Logged. Schematics + boarduniversal programming modulefirmware, drivers, software and so on. Originally from sprut:no settings to set; just do a Vpp calibration after u installed programmer on windowsa 3.3V Zenner diode in programmer is used as voltage reference for Vpp measuring. It is possible to use another diode and u need calibration of the programmer(i programed my 18f2550 with a simple jdm2 programmer, powered by serial port, with WinPic)works great tooeagle legalizer, if any of you need to recover old eagle files, created with cracked version of eagle(my files do open with freeware version)« Last Edit: January 20, 2007, 02:56:24 14:56 by eSilviu »Logged. ESilviu,Also, the guides if any for dsPIC.Thanks a lot friend.Iphoneinformation from winpic help(it works for dspic's tested by me)'Beware: The dsPIC30F2010's pinout looks similar to other PIC16F and PIC18F devices on first sight, but it is not compatible! The following table may help to build an adapter for most dsPIC's with 28 pin standard DIP case, to be programmed with an old 18-pin PIC programming interface:(.) About PGD and PGC filtering: There was a note on the Microchip forum (by Olin Lathrop) about programming the dsPIC30F201(.), suggesting to put 22.47 pF on the PGD and PGC lines to ground near the target chip.
In addition, put a 100 ohm resistor in series with the PGD line between target chip and the cap. The resistor and cap on the PGD line low pass filter the PGD signal when it is driven by the target chip. This reduces the high frequencies that can couple onto the PGC line. The cap on the PGC line makes it less suceptible to coupled noise.(.) We later found out that this important note also applies to the PIC18Fxxxx family. A user of a Velleman PIC programmer reported success with a PIC18F4520 after adding 2.
33 pF caps and a 100 Ohm series resistor.Logged. Schematics + boarduniversal programming modulefirmware, drivers, software and so on. Originally from sprut:no settings to set; just do a Vpp calibration after u installed programmer on windowsa 3.3V Zenner diode in programmer is used as voltage reference for Vpp measuring. It is possible to use another diode and u need calibration of the programmer(i programed my 18f2550 with a simple jdm2 programmer, powered by serial port, with WinPic)works great tooeagle legalizer, if any of you need to recover old eagle files, created with cracked version of eagle(my files do open with freeware version)Thanks very much for your effort & kindness.BTW, any plan for 'EagleLegaliser' to legalize eagle 4.16r2. I using this version.
GalepX for GALEP-5/5D/5F (gang programming software with script control). USB driver for Windows XP/Vista/7/8/8.1/10, G5Driver.zip, English/German. Pioneer bdr-xd07.
Anyway, dont worry. I also have eagle v4.16r1 & v4.16.« Last Edit: January 20, 2007, 09:07:04 09:07 by iphone »Logged. But did you realize the SHORT on the layout?? Download free canon ls 12pc ii manual software. Is it ok??FAIL!!!
The all pin cannot be SHORT as the 4 pins is for Vcc, Gnd, Data+ (D+) & Data- (D-).So, its need to be modified.is is so hard for you to cut the layout width a cutter?!!!!!!this is price for large pads on boardpictures posted are made with the files posted in forumHi, eSilviu, please don't mis-understand iphone, he just trying to make me understand because I'm start learning for PIC. Also iphone sorry for being mis-understanding by eSiliviu.
Thanks!!LoggedPages: 1.